Texas Instruments develops analog, digital signal processing, RF and DLP® semiconductor technologies that help customers deliver consumer and industrial electronics products with greater performance, increased power efficiency, higher precision, more mobility and better..
Texas Instruments
Showing 1–24 of 56 results
-
Amplifiers & Comparators
Texas Instruments LM358P
These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 32 V, and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage.
- Wide supply voltage ranges
- Low supply-current drain independent of supply voltage
- Common-mode input voltage range includes ground, allowing direct sensing near ground
- Low input bias and offset parameters
- Internal frequency compensation
SKU: W014506 -
Logic
Texas Instruments 74HC74N
The CD74HC74E is a high speed CMOS logic dual positive-edge-triggered D-type Flip-flop with set and reset. The HC74 utilizes silicon gate CMOS technology to achieve operating speeds equivalent to LSTTL parts. It exhibits the low power consumption of standard CMOS integrated circuits, together with the ability to drive 10 LSTTL loads. This flip-flop has independent DATA, SET\, RESET\ and CLOCK inputs and Q and Q\ outputs. The logic level present at the data input is transferred to the output during the positive-going transition of the clock pulse. SET\ and RESET\ are independent of the clock and are accomplished by a low level at the appropriate input.
- Hysteresis on clock inputs for improved noise immunity and increased input rise and fall times
- Asynchronous reset
- Complementary outputs
- Buffered inputs
- Balanced propagation delay and transition times
- Significant power reduction compared to LSTTL logic ICs
- ±20mA DC input/output diode current
- ±25mA DC drain current
SKU: W006370 -
Power Management ICs - PMIC
Texas Instruments 78SR105HC
Non-Isolated Step-Down (Buck) Power Modules, PTN, PTR, PTV, TPS Series, Texas Instruments
A range of PCB-mounting Step-down (Buck) switching voltage regulator modules from Texas Instruments. These products offer highly efficient space-saving solutions for low-power step-down DC-DC applications where isolation is not required.
SKU: W002899 -
Power Management ICs - PMIC
Texas Instruments 78ST105HC
Non-Isolated Step-Down (Buck) Power Modules, PTN, PTR, PTV, TPS Series, Texas Instruments
A range of PCB-mounting Step-down (Buck) switching voltage regulator modules from Texas Instruments. These products offer highly efficient space-saving solutions for low-power step-down DC-DC applications where isolation is not required.Non-Isolated Power Modules, Texas Instruments
Non-Isolated Power Modules are supporting designs which require superior EMI protection and thermal performance, high output current, high output voltage and more. The family of SIMPLE SWITCHER® power modules provides an all-in-one power solution to meet extreme operating conditions or simply a standard feature set, in a small, easy-to-use package.Integrated shielded inductor
Precision enable, soft-start, and tracking for sequencing
Best-in-class thermal performance
Pin-to-pin compatible modules for different load currents
Easy-to-use packaging
Passes EN55022 (CISPR22) Class B Radiated and Conducted EMI StandardSKU: W001047 -
Data & Signal Conversion
Texas Instruments ADS1015IDGST
The ADS1015IDGST is a Precision Analogue-to-digital Converter (ADC) with 12 bits of resolution. Designed with precision, power and ease of implementation in mind. It features an onboard reference and oscillator. Data are transferred via an I²C-compatible serial interface, four I²C slave addresses can be selected. It operates from a single power supply ranging from 2.0 to 5.5V. It can perform conversions at rates up to 3300 samples per second (SPS). An onboard PGA is available, that offers input ranges from the supply to as low as ±256mV, allowing both large and small signals to be measured with high resolution. Also features an input multiplexer (MUX) that provides two differential or four single-ended inputs. It operates either in continuous conversion mode or a single-shot mode that automatically powers down after a conversion and greatly reduces current consumption during idle periods.
- Low current consumption 128SPS to 3.3kSPS Programmable data rate
- Internal low-drift voltage reference
- Internal oscillator
- Internal PGA
- I²C Interface, pin-selectable addresses
- Four single-ended or two differential inputs
- Programmable comparator
SKU: W004545 -
Switches, Multiplexers & Demultiplexers
Texas Instruments CD4072BM96
The CD4052BM96 is a differential 4-channel Analog Multiplexer having two binary control inputs, A and B and an inhibit input. The two binary input signals select 1 of 4 pairs of channels to be turned on and connect the analog inputs to the outputs. The device is digitally-controlled analog switches having low ON impedance and very low OFF leakage current. These multiplexer circuits dissipate extremely low quiescent power over the full VDD-VSS and VDD-VEE supply-voltage ranges, independent of the logic state of the control signals. When logic 1 is present at the inhibit-input terminal, all channels are off.
- 125Ω (typical) Low ON resistance over 15VP-P
- 18V Signal input range for VDD – VEE
- ±100pA (Typical) High OFF resistance, channel leakage at VDD-VEE = 18 V
- Logic-level conversion for digital addressing signals
- Binary address decoding on chip
- 100% Tested for quiescent current at 20V
- 1µA Maximum input current at 18V over full package temperature range, 100nA at 18V and 25°C
- Break-before-make switching eliminates channel overlap
SKU: W007165 -
Amplifiers & Comparators
Texas Instruments INA215AIDCKT
The INA213AIDCKT is a voltage-output, Current Shunt Monitor, can sense drops across shunts at common-mode voltages from -0.3 to 26V, independent of the supply voltage. The low offset of the zero-drift architecture enables current sensing with maximum drops across the shunt as low as 10mV full-scale. This device operates from a single 2.7 to 26V power supply, drawing a maximum of 100µA of supply current.
- Wide common-mode voltage range (-0.3 to 26V)
- ±1% Gain error (max. over temp.), 0.5µV/°C offset drift (max.), 10ppm/°C gain drift (max.) accuracy
- 50V/V Gain
- 100µA (maximum) Quiescent current
- Green product and no Sb/Br
SKU: W005843 -
Drivers & Interfaces
Texas Instruments ISO1540DR
The ISO1540 and ISO1541 devices are low-power, bidirectional isolators that are compatible with I 2C interfaces. These devices have logic input and output buffers that are separated by Texas Instruments Capacitive Isolation technology using a silicon dioxide (SiO2 ) barrier. When used with isolated power supplies, these devices block high voltages, isolate grounds, and prevent noise currents from entering the local ground and interfering with or damaging sensitive circuitry.
This isolation technology provides for function, performance, size, and power consumption advantages when compared to optocouplers. The ISO1540 and ISO1541 devices enable a complete isolated I 2C interface to be implemented within a small form factor. The ISO1540 has two isolated bidirectional channels for clock and data lines while the ISO1541 has a bidirectional data and a unidirectional clock channel. The ISO1541 is useful in applications that have a single master while the ISO1540 is suitable for multimaster applications. For applications where clock stretching by the slave is possible, the ISO1540 device should be used.
SKU: W002726 -
Amplifiers & Comparators
Texas Instruments LM124DRG4
The LM124DRG4 is a 4 independent high-gain frequency-compensated Operational Amplifier designed specifically to operate from a single supply or split supply over a wide range of voltages.
- Internal frequency compensation
- Common-mode input voltage range includes ground, allowing direct sensing near ground
- Low input bias and offset parameters
- 2kV ESD Protection
- 0.8mA Typical low supply-current drain independent of supply voltage
- 3mV Typical input offset voltage
- 2nA Typical input offset current
- 20nA Typical input bias current
- 32V Differential input voltage range equal to maximum-rated supply voltage
- 100V/mV Typical open-loop differential voltage amplification
SKU: W010675 -
Amplifiers & Comparators
Texas Instruments LM124J
The LM124J is a low power quad Operational Amplifier designed to operate from a single power supply over a wide range of voltages. Operation from split-power supplies is also possible and the low-power supply current drain is independent of the magnitude of the power supply voltage. Application areas include transducer amplifiers, DC gain blocks and all the conventional op-amp circuits which now can be more easily implemented in single power supply systems. For example, the LM124 series can directly operate off of the standard 5V power supply voltage which is used in digital systems and easily provides the required interface electronics without requiring the additional ±15V power supplies.
- Internally frequency compensated for unity gain
- 45nA Low input biasing current
- 2mV Low input offset voltage
- 5nA Offsets current
- Input common-mode voltage range includes ground
- Differential input voltage range equal to the power supply voltage
- Military rated
SKU: W000094 -
-
Amplifiers & Comparators
Texas Instruments LM239N
The LMx39x and the LM2901x devices consist of four independent voltage comparators that are designed to operate from a single power supply over a wide range of voltages. Operation from dual supplies also is possible, as long as the difference between the two supplies is 2 V to 36 V, and VCC is at least 1.5 V more positive than the input common-mode voltage. Current drain is independent of the supply voltage. The outputs can be connected to other open-collector outputs to achieve wired-AND relationships.
The LM139 and LM139A devices are characterized for operation over the full military temperature range of –55°C to +125°C. The LM239 and LM239A devices are characterized for operation from –25°C to +85°C. The LM339 and LM339A devices are characterized for operation from 0°C to 70°C. The LM2901, LM2901AV, and LM2901V devices are characterized for operation from –40°C to +125°C.
SKU: W003932 -
Amplifiers & Comparators
Texas Instruments LM2900N
The LM2900N is a general purpose quadruple Norton Operational Amplifier consist of four independent, high-gain frequency-compensated Norton operational amplifiers that were designed specifically to operate from a single supply over a wide range of voltages. Operation from split supplies is also possible. The low supply current drain is essentially independent of the magnitude of the supply voltage. These devices provide wide band-width and large output voltage swing.
- Wide range of supply voltages, single or dual supplies
- Wide bandwidth
- Large output voltage swing
- Output short-circuit protection
- Internal frequency compensation
- Low input bias current
SKU: W002893 -
Amplifiers & Comparators
Texas Instruments LM2903M
The LM2903M is a dual differential Independent Voltage Comparator designed to operate from a single power supply over a wide voltage range. It features ±1 to ±18V dual supply operation, 800mA typical low current drain and 25nA typical low input bias current.
- Allows comparison of voltages near ground potential
- Compatible with all forms of logic
- 800µA Low current drain
- 25nA Low input bias current
- ±5nA Low input offset current
- ±1mV Low offset voltage
SKU: W007776 -
Power Management ICs - PMIC
Texas Instruments LM317AEMP
The LM317AEMP/NOPB is an adjustable 3-terminal positive Voltage Regulator is capable of supplying in excess of 1.5A over a 1.2 to 37V output range. It is exceptionally easy to use and require only two external resistors to set the output voltage. Further, both line and load regulations are better than standard fixed regulators. In addition to higher performance than fixed regulators, the LM317AEMP/NOPB series offers full overload protection available only in IC’s. Included on the chip are current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional even if the adjustment terminal is disconnected.
- Specified 1% Output Voltage Tolerance
- Specified Maximum 0.01%/V Line Regulation
- Specified 1.5A Output Current
- Adjustable Output Down to 1.2V
- Current Limit Constant with Temperature
- P+ Product Enhancement Tested
- 80dB Ripple Rejection
- Output is Short-circuit Protected
- Green Product, No Sb/Br
SKU: W001862 -
Power Management ICs - PMIC
Texas Instruments LM337IMP
The LM337IMP is a three terminal adjustable negative voltage regulator in 4 pin SOT-223 package. This regulator is exceptionally easy to apply and requires only two external resistors to set output voltage and one output capacitor for frequency compensation. The circuit design has been optimized for excellent regulation and low thermal transients. The LM137 features internal current limiting, thermal shut down and safe area compensation by making them virtually blowout proof against overloads. This positive voltage regulator is used in wide variety of applications including local on-card regulation, programmable output voltage regulation or precision current regulation.
- Adjustable output voltage from -1.2V to -37V
- 1.5A output current
- Input voltage range from -4.2V to -50V
- Line regulation is typically 0.01%/V
- Load regulation is typically 0.3%
- Excellent thermal regulation of 0.002%/W
- Ripple rejection ratio of 77dB
- Output is short circuit protected
- Operating temperature range -40°C to 125°C
- 50ppm/°C temperature coefficient
SKU: W022650 -
Power Management ICs - PMIC
Texas Instruments LM337T
The LM337T is an adjustable 3-terminal Negative Voltage Regulator, capable of supplying in excess of -1.5A over an output voltage range of -1.2V to -37V. This regulator is exceptionally easy to apply, requiring only 2 external resistors to set the output voltage and 1 output capacitor for frequency compensation. The circuit design has been optimized for excellent regulation and low thermal transients. Further, the LM137 series features internal current limiting, thermal shutdown and safe-area compensation, making them virtually blowout-proof against overloads. The LM337T serves a wide variety of applications including local on-card regulation, programmable-output voltage regulation or precision current regulation. The LM337T is ideal complements to the LM117/LM317 adjustable positive regulators.
- Output voltage adjustable from -1.2 to -37V
- 1.5A Output current specified, -55 to +150°C
- Line regulation typically 0.01%/V
- Load regulation typically 0.3%
- 0.002%/W Excellent thermal regulation
- 77dB Ripple rejection
- Excellent rejection of thermal transients
- 50ppm/°C Temperature coefficient
- Temperature-independent current limit
- Internal thermal overload protection
SKU: W012316 -
Power Management ICs - PMIC
Texas Instruments LM338T/NOPB
The LM338T/NOPB is an adjustable 3-terminal positive Voltage Regulator, capable of supplying in excess of 5A over a 1.2 to 32V output range. They are exceptionally easy to use and require only 2 resistors to set the output voltage. Careful circuit design has resulted in outstanding load and line regulation-comparable to many commercial power supplies. A unique feature of the LM338T/NOPB family is time-dependent current limiting. The current limit circuitry allows peak currents of up to 12A to be drawn from the regulator for short periods of time. This allows the LM338T/NOPB to be used with heavy transient loads and speeds start-up under full-load conditions. Under sustained loading conditions, the current limit decreases to a safe value protecting the regulator.
- Specified Thermal Regulation
- Current Limit Constant with Temperature
- P+ Product Enhancement Tested
- Output is Short-circuit Protected
- Green Product, No Sb/Br
SKU: W000346 -
Amplifiers & Comparators
Texas Instruments LM386N-1/NOPB
The LM386N-1/NOPB is a Wide Vin Class-D low Power Audio Amplifier with internal gain designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but the addition of an external resistor and capacitor between pins 1 and 8 will increase the gain to any value from 20 to 200. The inputs are ground referenced while the output automatically biases to one-half the supply voltage. The quiescent power drain is only 24mW when operating from a 6V supply, making the LM386 ideal for battery operation.
- Battery operation
- Minimum external parts
- Low quiescent current drain
- Ground referenced input
- Self-centering output quiescent voltage
- Green product and no Sb/Br
SKU: W006347 -
Amplifiers & Comparators
Texas Instruments LM4871MM/NOPB
The LM4871MM/NOPB is a mono bridged Audio Power Amplifier capable of delivering 3W of continuous average power into a 3R load with less than 10% THD when powered by a 5V power supply. To conserve power in portable applications, the LM4871's micropower shutdown mode (IQ = 0.6µA, typical) is activated when VDD is applied to the shutdown pin. Boomer audio power amplifier is designed specifically to provide high power, high fidelity audio output. It requires few external components and operates on low supply voltages from 2.0 to 5.5V. Since the LM4871 does not require output coupling capacitors, bootstrap capacitors or snubber networks, it is ideally suited for low-power portable systems that require minimum volume and weight. Additional LM4871 features include thermal shutdown protection, unity-gain stability and external gain set.
- No output coupling capacitors, bootstrap capacitors or snubber circuits are necessary
- Unity-gain stable
- External gain configuration capability
- Pin compatible with LM4861
- 0.6µA (typical) Shutdown current
- Green product and no Sb/Br
SKU: W004610 -
Amplifiers & Comparators
Texas Instruments LM7321MF/NOPB
The LM7321MF/NOPB is a single high output current Operational Amplifier with rail-to-rail input and output. The LM732xx family is efficient, achieving 18V/µs slew rate and 20MHz unity gain bandwidth while requiring only 1mA of supply current per op amp. The LM732xx device performance is fully specified for operation at 2.7V, ±5 and ±15V. The LM732xx device is designed to drive unlimited capacitive loads without oscillations. Greater than rail-to-rail input common-mode voltage range with 50dB of common-mode rejection across this wide voltage range, allows both high-side and low-side sensing. Most device parameters are insensitive to power supply voltage and this makes the parts easier to use where supply voltage may vary, such as automotive electrical systems and battery powered equipment. This amplifier has true rail-to-rail output and can supply a respectable amount of current (15mA) with minimal head-room from either rail (300mV) at low distortion (0.05% THD+noise).
- Capacitive load tolerance unlimited
- Input common-mode voltage of 0.3V beyond rails
- +65/-100mA Output current
- 15nV/√Hz Input voltage noise
- 1.3pA/√Hz Input current noise
- 1.1mA/channel Supply current
- -86dB Distortion THD+noise
- Green product and no Sb/Br
SKU: W000564 -
Power Management ICs - PMIC
Texas Instruments LP3853ES-2.5/NOPB
The LP3853/LP3856 series of fast ultra low-dropout linear regulators operate from a +2.5V to +7.0V input supply. Wide range of preset output voltage options are available. These ultra low dropout linear regulators respond very quickly to step changes in load, which makes them suitable for low voltage microprocessor applications. The LP3853/LP3856 are developed on a CMOS process which allows low quiescent current operation independent of output load current. This CMOS process also allows the LP3853/LP3856 to operate under extremely low dropout conditions.
SKU: W006995 -
Power Management ICs - PMIC
Texas Instruments LP38855S-1.2
The LP38855S-1.2 is a 1.8V fixed output fast-response high-accuracy low-dropout (LDO) Linear Regulator with Enable. The device can maintain output voltage regulation with an extremely low input to output voltage drop. Fabricated on a CMOS process, the device operates from two input voltages, VBIAS provides power for the internal bias and control circuits, as well as drive for the gate of the N-MOS power transistor, while VIN supplies power to the load. The use of an external bias rail allows the part to operate from ultra-low VIN voltages. Unlike bipolar regulators, the CMOS architecture consumes extremely low quiescent current at any output load current. The use of an N-MOS power transistor results in wide bandwidth, yet minimum external capacitance is required to maintain loop stability. The fast transient response of this device makes it suitable for use in powering DSP, microcontroller core voltages and switch mode power supply post regulators.
- Stable with 10µF ceramic capacitors
- ±1.0% Precision output voltage across all line and load conditions (TJ = 25°C)
- Overtemperature and overcurrent protection
SKU: W002951 -
Power Management ICs - PMIC
Texas Instruments LP3963ES-3.3/NOPB
The LP3963ES-3.3/NOPB is a 3.3V fixed output fast ultra-low-dropout (LDO) Linear Regulator operate from a 2.5 to 7V input supply. This device respond very fast to step changes in load which makes them suitable for low voltage microprocessor applications. The device is developed on a CMOS process which allows low quiescent current operation independent of output load current. This CMOS process also allows the device to operate under extremely low-dropout (LDO) conditions. The dropout voltage is typically 80mV at 300mA load current and 800mV at 3A load current.
- Low ground pin current
- 0.06% Load regulation
- 15µA Quiescent current in shutdown mode
- ±1.5% Output voltage accuracy
- ERROR flag indicates output status
- Minimum output capacitor requirements
- Overtemperature and overcurrent protection
SKU: W006996