25.0 V (max), 3.30 V (min)
|Number of Pins||
-40.0 °C (min)
|Number of Outputs||
|Manufacturer||Analog Devices / Linear Technology|
|Manufacturer Part Number||LTM8064EY#PBF|
|Description||DC DC CONVERTER 1.2-36V|
The LTM®8064 is a 58VIN, 6A, constant-voltage, constantcurrent (CVCC), step-down µModule® (power module) regulator. Included in the package are the switching controller, power switches, inductor andsupport components. Operating over an input voltage range of 6V to 58V, the LTM8064 supports an output voltage range of 1.2V to 36V. CVCC operation allows the LTM8064 to accurately regulate its output current up to 7A when sourcing and 9.1A when sinking over the entire output range. The output current can be set by a control voltage, a single resistor or a thermistor. To set the switching frequency, simply place a resistor from the RT pin to ground. A resistor from FB to ground will set the output voltage. Only the bulk input and output filter capacitors are needed to finish the design.
Non-Isolated PoL Module DC DC Converter 1 Output 1.2 ~ 36V 6A 6V – 58V Input
TDK-Lambda DPP50-240 out of 5(0)
The DPP50-24 is a 24V/50W 1-output DIN-rail mount Power Supply features a compact size universal input, convection cooled, greater than 120% over-current protection 125 to 137.5%, cycle AC line to reset overvoltage protection. This power supply supports global use, easier system configuration and integration. This power supply output is fixed and can be adjustable.
- <50mV (20MHz bandwidth) Ripple/noise
- 86% Efficiency
- >20ms Hold-up time (115VAC input)
- -10 to 71°C Operating temperature range
Recom Power RPA30-2405SAW/P0 out of 5(0)
The RPA30-2405SAW/P from Recom Power is a RPA30-AW series 30W single output DC to DC converter with positive control function. This high power density converter has 4:1 wide input voltage range and industry standard 1"x1" case size. Despite its small size, the RPA30-AW converter is fully specified device with high efficiency, no minimum load, 1600VDC isolation, tight regulation and low ripple/noise figures. This single output DC to DC converter offers a ±10% trim range. The outputs are also fully protected against overtemperature, short circuits, overcurrent and overvoltage. The converter finds many uses in railway applications where board space is at a premium. It has Pi-Type internal input filter.
- Input voltage range from 9VDC to 36VDC (24VDC nominal input voltage)
- Output voltage of 5VDC and output current of 6000mA
- Input current of 1450mA
- Efficiency of 89% and maximum capacitive load of 10000µF
- Maximum line regulation of ±0.2%
- Load regulation of ±0.2%
- Start-up time of 8ms (power-up, CTRL ON/OFF) and internal operating frequency of 550KHz
- Ripple and noise of 50mVp-p and maximum output accuracy of ±2.0%
- Minimum isolation resistance of 10Mohm and typical isolation capacitance of 1100pF
- Maximum case temperature of 105°C
Vicor VI-JT3-EX0 out of 5(0)
The VI-J00 MiniMod family established a new standard in component-level DC-DC converters. This “junior” size complement to the higher power VI-200 family offers up to 100W of isolated and regulated power in a board mounted package. With thousands of input/output/power combinations, and with a maximum operating temperature rating of 100°C, the MiniMod provides nearly unlimited flexibiliy for power system designers to meet demanding time to market requirements.
Utilizing Vicor’s “zero-current-switching” forward converter technology, proven by an installed base of over 8 million units, the MiniMod family combines state of the art power density with theSKU: W005262
Bel Fuse 40IMX4-1212-80 out of 5(0)
The IMX4 Series of board-mountable 4-watt DC-DC converters has been designed according to the latest industry requirements and standards. The converters are particularly suitable for use in mobile or stationary applications in transport, industry, or telecom, where variable input voltages or high transient voltages are prevalent. Covering a total input voltage range from 8.4 VDC up to 121 VDC with three different models, the converters are available with single or dual output from 3.3 up to _ VDC with flexible load distribution.SKU: W000007
Murata Power Solutions NME0505SC0 out of 5(0)
The NME0505SC from Murata is an isolated, 1W, single output DC to DC converter in SIP package. It is particularly suited to isolate or converting DC power rails. The galvanic isolation allows the device to configure an isolated negative rail in systems where only positive rails exist.
The NME series of DC-DC Converters is particularly suited to isolating and/or converting DC power rails. The galvanic isolation allows the device to be configured to provide an isolated negative rail in systems where only positive rails exist. The wide temperature range guarantees startup from –40°C and full 1 watt output at 85°C2 . For lower ripple, refer to output ripple reduction section.
The NME series offers short circuit protection options (PC) across the operating temperature range. Short circuits of less than 1Ω cause the converter to enter a ‘foldback’ limiting mode such that the input current is approximately 95mA for 0505 variant. Protection is continuous and auto-resetting on removal of the short circuitSKU: W000006