REACH SVHC Compliance | No SVHC |
---|---|
Packaging | Tube |
RoHS | Compliant |
Supply Current | 18.5 mA |
Number of Pins | 8 |
Operating Temperature | -40.0 °C (min) |
Mounting Style | Surface Mount |
Bandwidth | 200 kHz |
Lead-Free Status | Lead Free |
Lifecycle Status | Active |
Isolation Voltage | 5.00 kV |
Manufacturer | Broadcom |
---|---|
Manufacturer Part Number | ACPL-C79B-000E |
Description | IC OPAMP ISOLATION 200KHZ 8SO |
Stock Code | W005353 |
Download | ![]() |
The ACPL-C79B-000E is a precision miniature Isolation Amplifier designed for current and voltage sensing in electronic power converters. It operates from a single 5V supply and provides excellent linearity and dynamic performance of 60dB SNR. The amplifier with 200kHz bandwidth, 1.6µs fast response time, the product captures transients in short-circuit and overload conditions. The high common-mode transient immunity provides the precision and stability needed to accurately monitor motor current in high noise motor control environments, providing for smoother control in various types of motor control applications. In a typical motor drive implementation, current flows through an external resistor and the resulting analogue voltage drop is sensed by the isolation amplifier.
- Advanced sigma-delta A/D converter technology
- Fully differential isolation amplifier
- Compact and auto-insertable standard
- 15kV/μs Common-mode transient immunity
- 0.05% Excellent linearity
Related products
- Amplifiers & Comparators
Texas Instruments LM7321MF/NOPB
0 out of 5(0)The LM7321MF/NOPB is a single high output current Operational Amplifier with rail-to-rail input and output. The LM732xx family is efficient, achieving 18V/µs slew rate and 20MHz unity gain bandwidth while requiring only 1mA of supply current per op amp. The LM732xx device performance is fully specified for operation at 2.7V, ±5 and ±15V. The LM732xx device is designed to drive unlimited capacitive loads without oscillations. Greater than rail-to-rail input common-mode voltage range with 50dB of common-mode rejection across this wide voltage range, allows both high-side and low-side sensing. Most device parameters are insensitive to power supply voltage and this makes the parts easier to use where supply voltage may vary, such as automotive electrical systems and battery powered equipment. This amplifier has true rail-to-rail output and can supply a respectable amount of current (15mA) with minimal head-room from either rail (300mV) at low distortion (0.05% THD+noise).
- Capacitive load tolerance unlimited
- Input common-mode voltage of 0.3V beyond rails
- +65/-100mA Output current
- 15nV/√Hz Input voltage noise
- 1.3pA/√Hz Input current noise
- 1.1mA/channel Supply current
- -86dB Distortion THD+noise
- Green product and no Sb/Br
SKU: W000564 - Amplifiers & Comparators
Texas Instruments OPA340NA/3K
0 out of 5(0)The OPA340NA/3K is a single-supply Operational Amplifier optimized for low-voltage. High-speed operation make them ideal for driving sampling analogue-to-digital (A/D) converters. They are also well-suited for general purpose and audio applications as well as providing I/V conversion at the output of digital-to-analogue (D/A) converters. Single version have identical specifications for design flexibility. The OPA340 series operate on a single supply as low as 2.5V with an input common-mode voltage range that extends 500mV below ground and 500mV above the positive supply. Output voltage swing is to within 1mV of the supply rails with a 100k load.
- Rail-to-rail input/output
- 750µA/channel Low quiescent current
- Green product and no Sb/Br
SKU: W020494 - Amplifiers & Comparators
Texas Instruments LM124DRG4
0 out of 5(0)The LM124DRG4 is a 4 independent high-gain frequency-compensated Operational Amplifier designed specifically to operate from a single supply or split supply over a wide range of voltages.
- Internal frequency compensation
- Common-mode input voltage range includes ground, allowing direct sensing near ground
- Low input bias and offset parameters
- 2kV ESD Protection
- 0.8mA Typical low supply-current drain independent of supply voltage
- 3mV Typical input offset voltage
- 2nA Typical input offset current
- 20nA Typical input bias current
- 32V Differential input voltage range equal to maximum-rated supply voltage
- 100V/mV Typical open-loop differential voltage amplification
SKU: W010675 - Amplifiers & Comparators
Analog Devices AD8244BRMZ
0 out of 5(0)The AD8244BRMZ is a low power FET input quad Unity-gain Buffer designed to isolate very large source impedances from the rest of the signal chain. The 2pA maximum bias current, near zero current noise and 10 TΩ input impedance introduce almost no error, even with source impedance well into the megaohms. Many traditional operational amplifier pinouts have a supply pin that is next to the non-inverting input. A guard trace must be routed between these pins to avoid leakage currents much larger than the bias current of a FET input op amp. The AD8244 solves this problem with unique pinout that physically separates the high impedance inputs from the low impedance supplies and outputs of the other buffers. The AD8244 design is focused on solving problems specific to buffers. This includes close channel-to-channel matching which allows channels of the AD8244 to be used in differential signal chains with minimal error.
- Extremely high input impedance
- Low noise
- High DC precision – 3μV/°C maximum offset drift (B grade)
- No leakage from inputs to supply pins
- Provides guarding capability
- Rail-to-rail output
- Single-supply operation – Input range extends to ground
- 250μA Maximum supply current per amplifier
- 2pA Maximum input bias current at 25°C
SKU: W004537 - Amplifiers & Comparators
Texas Instruments LM358P
0 out of 5(0)These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 32 V, and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage.
- Wide supply voltage ranges
- Low supply-current drain independent of supply voltage
- Common-mode input voltage range includes ground, allowing direct sensing near ground
- Low input bias and offset parameters
- Internal frequency compensation
SKU: W014506