|REACH SVHC Compliance||
|Number of Outputs||
|Manufacturer||Murata Power Solutions|
|Manufacturer Part Number||MTU1D0512MC|
|Description||Isolated DC/DC Converters 1W 5Vin 12Vout 83mA Dual SMT|
The MTU2D0512MC is a 2-output 2W board-mount isolated DC/DC Converter with a footprint reduction of over 50% from the previous generations. The device is more efficient and offers improved regulation performance for applications where a wide output voltage variation cannot be tolerated. The device is pin compatible with the MTU2 series. The device is suitable for all applications where high volume production is envisaged.
- Patent protected
- Multi-layer ceramic capacitors
- 1kVDC Isolation hi pot test
- Footprint over pins 0.69cm²
- Power density 3.403W/cm³
- 11% Maximum load regulation
- 35mVp-p Maximum ripple and noise
- 85% Typical efficiency
- 19pF Isolation capacitance
- 880μs Start-up time
Murata Power Solutions NME0505SC0 out of 5(0)
The NME0505SC from Murata is an isolated, 1W, single output DC to DC converter in SIP package. It is particularly suited to isolate or converting DC power rails. The galvanic isolation allows the device to configure an isolated negative rail in systems where only positive rails exist.
The NME series of DC-DC Converters is particularly suited to isolating and/or converting DC power rails. The galvanic isolation allows the device to be configured to provide an isolated negative rail in systems where only positive rails exist. The wide temperature range guarantees startup from –40°C and full 1 watt output at 85°C2 . For lower ripple, refer to output ripple reduction section.
The NME series offers short circuit protection options (PC) across the operating temperature range. Short circuits of less than 1Ω cause the converter to enter a ‘foldback’ limiting mode such that the input current is approximately 95mA for 0505 variant. Protection is continuous and auto-resetting on removal of the short circuitSKU: W000006
Recom Power RPA30-2405SAW/P0 out of 5(0)
The RPA30-2405SAW/P from Recom Power is a RPA30-AW series 30W single output DC to DC converter with positive control function. This high power density converter has 4:1 wide input voltage range and industry standard 1"x1" case size. Despite its small size, the RPA30-AW converter is fully specified device with high efficiency, no minimum load, 1600VDC isolation, tight regulation and low ripple/noise figures. This single output DC to DC converter offers a ±10% trim range. The outputs are also fully protected against overtemperature, short circuits, overcurrent and overvoltage. The converter finds many uses in railway applications where board space is at a premium. It has Pi-Type internal input filter.
- Input voltage range from 9VDC to 36VDC (24VDC nominal input voltage)
- Output voltage of 5VDC and output current of 6000mA
- Input current of 1450mA
- Efficiency of 89% and maximum capacitive load of 10000µF
- Maximum line regulation of ±0.2%
- Load regulation of ±0.2%
- Start-up time of 8ms (power-up, CTRL ON/OFF) and internal operating frequency of 550KHz
- Ripple and noise of 50mVp-p and maximum output accuracy of ±2.0%
- Minimum isolation resistance of 10Mohm and typical isolation capacitance of 1100pF
- Maximum case temperature of 105°C
Vicor VI-J43-CX0 out of 5(0)
A range of board-mount AC front-end modules is available for the design of a full AC-DC power system. Global, autoranging input ranges are available from 85 to 264 Vac at 47 to 63 Hz.
The isolated, power factor corrected devices integrate EMI/RFI filtering, transient protection, short circuit protection and inrush limiting to simplify design. These building block components enable high-density power solutions (from 330 W to 1500 W), meeting necessary worldwide standards, including compliance to EMC standards for harmonic currents, line disturbance and transient conducted emissions.SKU: W003133
Murata Power Solutions OKL-T/6-W12N-C0 out of 5(0)
The OKL-T/6-W12 series are miniature non-isolated PoL SMT DC/DC Power Converters for embedded applications. Featuring inspectable Land Grid Array ( iLGA) format, the OKL-T/6-W12N-C measures only 12.2 x 12.2 x 7.2mm maximum. Based on fixed-frequency synchronous buck converter switching topology, the high power conversion efficient point-of-load (PoL) module features programmable output voltage and on/off control. This converter also include under-voltage lock out (UVLO), output short-circuit protection and over-current protections. An optional sequence/tracking feature on OKL-T/6-W12N-C allows power sequencing of PoLs.
- iLGA inspectable Land Grid Array
- Programmable output voltage from 0.591 to 5.5VDC
- Drives up to 300μF ceramic capacitive loads
- High power conversion efficiency at 93%
- Outstanding thermal derating performance
- Short-circuit and over-current protection
- On/off control and power good signal