|Supply Voltage (DC)||
|REACH SVHC Compliance||
|Number of Outputs||
|Input Voltage (DC)||
4.50 V to 5.50 V
1.00 W (max)
|Manufacturer||Murata Power Solutions|
|Manufacturer Part Number||MTU1S0505MC|
|Description||ISOLATED DC/DC, 5V IN, 5V OUT, 200mA, 1W|
The MTU1S0505MC is a 1-output board-mount isolated SM DC to DC Converter with a footprint reduction of over 50% from the previous generation of 1W SMD DC/DC converter. The MTU1 series is more efficient and offers improved regulation performance for applications where a wide output voltage variation cannot be tolerated. The device is suitable for all applications where high volume production is envisaged.
- Patent protected
- Footprint over pins 0.69cm²
- 1kVDC Isolation ‘Hipot Test’
- Efficiency up to 88% typical
- 1.7W/cm³ Power density
- Toroidal magnetics
- Multi-layer ceramic capacitors
- -40 to +85°C Wide operating temperature range
Murata Power Solutions NME0505SC0 out of 5(0)
The NME0505SC from Murata is an isolated, 1W, single output DC to DC converter in SIP package. It is particularly suited to isolate or converting DC power rails. The galvanic isolation allows the device to configure an isolated negative rail in systems where only positive rails exist.
The NME series of DC-DC Converters is particularly suited to isolating and/or converting DC power rails. The galvanic isolation allows the device to be configured to provide an isolated negative rail in systems where only positive rails exist. The wide temperature range guarantees startup from –40°C and full 1 watt output at 85°C2 . For lower ripple, refer to output ripple reduction section.
The NME series offers short circuit protection options (PC) across the operating temperature range. Short circuits of less than 1Ω cause the converter to enter a ‘foldback’ limiting mode such that the input current is approximately 95mA for 0505 variant. Protection is continuous and auto-resetting on removal of the short circuitSKU: W000006
XP Power JCG1524S050 out of 5(0)
The JCG series from XP Power offers a highly reliable range of single and dual output, 12/15 W, isolated DC-DC converters. This compact range attributes 1600 VDC in isolation, a 2:1 input range and high power density. The series is available in an industry standard package, features remote on/off settings and has a high efficiency of up to 91%.
- High Power Density
- 2:1 Input Range
- Operating Temperature: -40°C to +100°C
- Metal Case
- Efficiency up to 91%
- Remote On/Off
- 1600 VDC Isolation
Bel Fuse 40IMX4-1212-80 out of 5(0)
The IMX4 Series of board-mountable 4-watt DC-DC converters has been designed according to the latest industry requirements and standards. The converters are particularly suitable for use in mobile or stationary applications in transport, industry, or telecom, where variable input voltages or high transient voltages are prevalent. Covering a total input voltage range from 8.4 VDC up to 121 VDC with three different models, the converters are available with single or dual output from 3.3 up to _ VDC with flexible load distribution.SKU: W000007
Analog Devices / Linear Technology LTM8064EY#PBF0 out of 5(0)
The LTM®8064 is a 58VIN, 6A, constant-voltage, constantcurrent (CVCC), step-down µModule® (power module) regulator. Included in the package are the switching controller, power switches, inductor andsupport components. Operating over an input voltage range of 6V to 58V, the LTM8064 supports an output voltage range of 1.2V to 36V. CVCC operation allows the LTM8064 to accurately regulate its output current up to 7A when sourcing and 9.1A when sinking over the entire output range. The output current can be set by a control voltage, a single resistor or a thermistor. To set the switching frequency, simply place a resistor from the RT pin to ground. A resistor from FB to ground will set the output voltage. Only the bulk input and output filter capacitors are needed to finish the design.
Non-Isolated PoL Module DC DC Converter 1 Output 1.2 ~ 36V 6A 6V – 58V InputSKU: W023610