| RoHS | Compliant |
|---|---|
| Lead-Free Status | Lead Free |
| Lifecycle Status | Active |
| Gain Bandwidth Product | 700 kHz |
| Mounting Style | Through Hole |
| Bandwidth | 1.00 MHz |
| Case/Package | PDIP |
| Number of Channels | 2 |
| Packaging | Tube |
| REACH SVHC Compliance | No SVHC |
| Slew Rate | 300 mV/μs |
| Number of Pins | 8 |
| Number of Circuits | 2 |
| Supply Current | 2.00 mA (max) |
| Operating Temperature | 0.00 °C to 70.0 °C |
| Input Offset Drift | 7.00 µV/K |
Amplifiers & Comparators
| Manufacturer | Texas Instruments |
|---|---|
| Manufacturer Part Number | LM358P |
| Description | IC OPAMP GP 700KHZ 8DIP |
| Stock Code | W014506 |
| Download |  Technical Datasheet |
These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 32 V, and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage.
- Wide supply voltage ranges
- Low supply-current drain independent of supply voltage
- Common-mode input voltage range includes ground, allowing direct sensing near ground
- Low input bias and offset parameters
- Internal frequency compensation
Related products
- Amplifiers & Comparators
Texas Instruments LM7321MF/NOPB
The LM7321MF/NOPB is a single high output current Operational Amplifier with rail-to-rail input and output. The LM732xx family is efficient, achieving 18V/µs slew rate and 20MHz unity gain bandwidth while requiring only 1mA of supply current per op amp. The LM732xx device performance is fully specified for operation at 2.7V, ±5 and ±15V. The LM732xx device is designed to drive unlimited capacitive loads without oscillations. Greater than rail-to-rail input common-mode voltage range with 50dB of common-mode rejection across this wide voltage range, allows both high-side and low-side sensing. Most device parameters are insensitive to power supply voltage and this makes the parts easier to use where supply voltage may vary, such as automotive electrical systems and battery powered equipment. This amplifier has true rail-to-rail output and can supply a respectable amount of current (15mA) with minimal head-room from either rail (300mV) at low distortion (0.05% THD+noise).
- Capacitive load tolerance unlimited
- Input common-mode voltage of 0.3V beyond rails
- +65/-100mA Output current
- 15nV/√Hz Input voltage noise
- 1.3pA/√Hz Input current noise
- 1.1mA/channel Supply current
- -86dB Distortion THD+noise
- Green product and no Sb/Br
SKU: W000564 - Amplifiers & Comparators
Vishay SFH6916
The SFH6916 is a 4-channel Phototransistor Output Optocoupler has a GaAs infrared emitter, which is optically coupled to a silicon planar phototransistor detector. It features a high current transfer ratio, low coupling capacitance and high isolation voltage. The coupling device is designed for signal transmission between two electrically separated circuits.
- Low saturation voltage
- Fast switching times
- Temperature stable
SKU: W005455 - Amplifiers & Comparators
Texas Instruments LM124DRG4
The LM124DRG4 is a 4 independent high-gain frequency-compensated Operational Amplifier designed specifically to operate from a single supply or split supply over a wide range of voltages.
- Internal frequency compensation
- Common-mode input voltage range includes ground, allowing direct sensing near ground
- Low input bias and offset parameters
- 2kV ESD Protection
- 0.8mA Typical low supply-current drain independent of supply voltage
- 3mV Typical input offset voltage
- 2nA Typical input offset current
- 20nA Typical input bias current
- 32V Differential input voltage range equal to maximum-rated supply voltage
- 100V/mV Typical open-loop differential voltage amplification
SKU: W010675 - Amplifiers & Comparators
Microchip MCP6292-E/MS
The MCP6292-E/MS is a 10MHz rail-to-rail Operational Amplifier provides wide bandwidth for the current. It features a gain bandwidth product (GBWP) and a 65° phase margin. This family also operates from a single supply voltage as low as 2.4V, while drawing 1mA (typical) quiescent current. Additionally, the MCP6291 supports rail-to-rail input and output swing, with a common mode input voltage range of +300mV VDD to -300mV VSS. This family of operational amplifiers is designed with an advanced CMOS process.
- ±3mV Maximum input offset voltage
- 65dB (typical) Common mode rejection ratio
- 70dB Typical power supply rejection ratio
SKU: W022806 - Amplifiers & Comparators
Broadcom HCPL-7800-000E
The HCPL-7800-000E is an Isolation Amplifier for current sensing in electronic motor drives. The high CMR capability of isolation amplifier provides the precision and stability needed to accurately monitor motor current in high noise motor control environments, providing for smoother control in various types of motor control applications. In a typical implementation the motor current flows through an external resistor and the resulting analogue voltage drop is sensed by the amplifier. A differential output voltage is created on the other side of the amplifier optical isolation barrier. It is designed to ignore very high common-mode transient slew rates.
- 15kV/µs Common-mode rejection at VCM = 1000V
- Advanced sigma-delta A/D converter technology
- Compact and auto-insertable
- Fully differential circuit topology
SKU: W003181
