|Number of Pins||
|Supply Voltage (DC)||
5.50 V (max), 2.70 V (min)
Cut Tape (CT)
-40.0 °C to 125 °C
|Number of Bits||
|Manufacturer Part Number||TMP275AIDGKR|
|Description||SENSOR TEMPERATURE SMBUS 8VSSOP|
The TMP275 is a 0.5°C accurate, Two-Wire, serial output temperature sensor available in an MSOP-8 or an SO-8 package. The TMP275 is capable of reading temperatures with a resolution of 0.0625°C. The TMP275 is SMBus-compatible and allows up to eight devices on one bus.
It is ideal for extended temperature measurement in a variety of communication, computer, consumer, environmental, industrial, and instrumentation applications. The TMP275 is specified for operation over a temperature range of −40°C to +125°C.
Analog Devices ADT7410TRZ0 out of 5(0)
The ADT7410 is a high accuracy digital temperature sensor in both a narrow SOIC package and a 4 mm × 4 mm LFCSP package. It contains a band gap temperature reference and a 13-bit ADC to monitor and digitize the temperature to a 0.0625°C resolution. The ADC resolution, by default, is set to 13 bits (0.0625°C). This can be changed to 16 bits (0.0078°C) by setting Bit 7 in the configuration register (Register Address 0x03). The ADT7410 is guaranteed to operate over supply voltages from 2.7 V to 5.5 V. Operating at 3.3 V, the average supply current is typically 210 μA.
The ADT7410 has a shutdown mode that powers down the device and offers a shutdown current of typically 2 μA. The ADT7410 is rated for operation over the −55°C to +150°C temperature range. Pin A0 and Pin A1 are available for address selection, giving the ADT7410 four possible I2 C addresses. The CT pin is an opendrain output that becomes active when the temperature exceeds a programmable critical temperature limit. The default critical temperature limit is 147°C. The INT pin is also an open-drain output that becomes active when the temperature exceeds a programmable limit. The INT and CT pins can operate in either comparator or interrupt mode.
- Medical equipment
- Environmental control systems
- Computer thermal monitoring
- Thermal protection
- Industrial process control
- Power system monitors
- Hand-held applications
NXP Semiconductors MPL3115A20 out of 5(0)
The Xtrinsic MPL3115A2 employs a MEMS pressure sensor with an I2C interface to provide accurate Pressure/Altitude and Temperature data. The sensor outputs are digitized by a high resolution 24-bit ADC. Internal processing removes compensation tasks from the host MCU system. Multiple user-programmable , power saving, interrupt and autonomous data acquisition modes are available, including programmed acquisition cycle timing, and poll-only modes. Typical active supply current is 40 μA per measurement-second for a stable 10 cm output resolution.
- Fully compensated internally
- Programmable events
- Autonomous data acquisition
- Resolution down to 0.1 m
- 32-sample FIFO
- Ability to log data up to 12 days using the FIFO
- 1 second to 9 hour data acquisition rate
- I2C digital output interface
Texas Instruments TMP100NA/3K0 out of 5(0)
The TMP100NA/3K is a Digital Temperature Sensor ideal for negative temperature coefficient (NTC) and positive temperature coefficient (PTC) thermistor replacement. The devices offer a typical accuracy of ±1°C without requiring calibration or external component signal conditioning. Device temperature sensors are highly linear and do not require complex calculations or look-up tables to derive the temperature. The on-chip, 12-bit ADC offers resolutions down to 0.0625°C. The devices feature SMBus, 2-wire and I²C interface compatibility. The device allows up to eight devices on one. The TMP101 device offers a SMBus Alert function with up to three devices per bus.
- 9 to 12-bit User-selectable resolution
- 2 Address pins
- 45µA Low quiescent current
Analog Devices TMP36FSZ0 out of 5(0)
The TMP36FSZ is a Low Voltage Temperature Sensor that provides a voltage output that is linearly proportional to the Celsius (centigrade) temperature. It do not require any external calibration to provide typical accuracies of ±1°C at +25°C and ±2°C over the -40 to +125°C temperature range. The low output impedance of the TMP36 and its linear output and precise calibration simplify interfacing to temperature control circuitry and ADCs.
This sensor is intended for single-supply operation from 2.7 to 5.5V maximum. The supply current runs well below 50µA, providing very low self-heating less than 0.1°C in still air. In addition, a shutdown function is provided to cut the supply current to less than 0.5µA.
The TMP36 is specified from -40 to +125°C, provides a 750mV output at 25°C and operates to 125°C from a single 2.7V supply. It has an output scale factor of 10mV/°C and functionally compatible with the LM50.SKU: W021512
Analog Devices AD22279-A-R20 out of 5(0)
The ADXL78 series low power, high-g 1-axis Accelerometer with signal conditioned voltage outputs that are on a single monolithic IC. This product measures acceleration with a full-scale range of ±35g, ±50g or ±70g (minimum). It can also measure both dynamic acceleration (vibration) and static acceleration (gravity). The device is the fourth-generation surface micro machined iMEMS® accelerometer from ADI with enhanced performance. The device is temperature stable and accurate over the automotive temperature range, with a self-test feature that fully exercises all the mechanical and electrical elements of the sensor with a digital signal applied to a single pin. Full differential sensor and circuitry for high resistance to EMI/RFI
- Complete mechanical and electrical self-test on digital command
- Output ratiometric to supply
- Sensitive axes in the plane of the chip
- High linearity (0.2% of full scale)
- Frequency response down to DC
- Low noise
- Low power consumption (1.3mA)
- Tight sensitivity tolerance and 0 g offset capability
- Largest available prefilter clipping headroom
- 400Hz, 2-pole Bessel filter
- Single-supply operation