RoHS | Compliant |
---|---|
Quiescent Current | 530 µA |
Number of Pins | 10 |
Supply Voltage (DC) | 4.20 V (min), 4.50 V (min), 52.0 V (max) |
Thermal Shutdown | No |
REACH SVHC Compliance | No SVHC |
Topology | Boost |
Packaging | Tape & Reel (TR) |
Output Voltage | 60.0 V |
Lead-Free Status | Lead Free |
Frequency | 1.00 MHz |
Number of Regulated Outputs | 1 |
Output Current | 6.00 A |
Operating Temperature | -40.0 °C (min) |
Lifecycle Status | Active |
Manufacturer | Texas Instruments |
---|---|
Manufacturer Part Number | TPS40210QDGQRQ1 |
Description | Boost Controller, 4.5-52V 10MSOP |
Stock Code | W005251 |
Download | ![]() |
The TPS40210QDGQRQ1 is a current-mode Boost Controller suitable for topologies that require a grounded source N-channel FET, including boost, flyback, SEPIC and various LED driver applications. This device features include programmable soft start, overcurrent protection with automatic retry and programmable oscillator frequency. Current- mode control provides improved transient response and simplified loop compensation. The main difference between the two parts is the reference voltage to which the error amplifier regulates the FB pin.
- Adjustable oscillator frequency
- Fixed-frequency current-mode control
- Internal slope compensation
- Integrated low-side driver
- Programmable closed-loop soft star
- Overcurrent protection
- External synchronization capable
- Low-current disable function
- Green product and no Sb/Br
Related products
-
Power Management ICs - PMIC
Texas Instruments TPS27081ADDCR
0 out of 5(0)The TPS27081ADDCR is a high-side Load Switch features industry-standard ESD protection on all pins providing better ESD compatibility with other on board components. The TPS27081A level shifts ON/OFF logic signal to VIN levels and supports as low as 1-V CPU or MCU logic to control higher voltage power supplies without requiring an external level-shifter. Switching a large value output capacitor CL through a fast ON/OFF logic signal may result in an excessive inrush current. To control the load inrush current, connect a resistor R2 and add an external capacitor C1 as shown in the Simplified Schematic in the Technical Data Sheet. To configure the TPS27081A to achieve a specific slew rate, refer to the Application and Implementation section. A single pull-up resistor R1 is required in standby power switch applications. In such applications connect the R2 pin of the TPS27081A to the system ground when inrush current control is not required.
- Adjustable turn-on and turnoff slew rate control through external R1, R2 and C1
- Supports a wide range of 1.2 to 8V supply inputs
- Integrated NMOS for PFET control
- Full ESD protection (all pins)
- Low ON-resistance, high-current PFET
- Ultralow leakage current in standby (typical 100nA)
SKU: W008212 -
Power Management ICs - PMIC
Texas Instruments TPS73701DCQ
0 out of 5(0)The TPS73701DCQ is a linear low-dropout (LDO) Voltage Regulator uses an NMOS pass element in a voltage-follower configuration. This topology is relatively insensitive to output capacitor value and ESR, allowing a wide variety of load configurations. Load transient response is excellent, even with a small 1µF ceramic output capacitor. The NMOS topology also allows very low dropout. This device uses an advanced BiCMOS process to yield high precision while delivering very low dropout voltages and low ground pin current. Current consumption, when not enabled, is less than 20nA and ideal for portable applications. This device is protected by thermal shutdown and fold-back current limit. It features reverse current blockage and freedom from output capacitor constraints. These features combined with an enable input makes the device ideal for portable applications.
- Thermal shutdown and current limit for fault protection
- Excellent load transient response-even with only 1µF output capacitor
- 1% Initial accuracy
- 3% Overall accuracy over line, load and temperature
- Less than 20nA typical IQ in shutdown mode
- Green product and no Sb/Br
SKU: W000341 -
Power Management ICs - PMIC
Analog Devices / Linear Technology LTC4151IMS#PBF
0 out of 5(0)The LTC®4151 is a high side power monitor that operates over a wide voltage range of 7V to 80V. In default operation mode, the onboard 12-bit ADC continuously measures high side current, input voltage and an external voltage. Data is reported through the I2C interface when polled by a host. The LTC4151 can also perform on-demand measurement in a snapshot mode.
The LTC4151 features a dedicated shutdown pin to reduce power consumption. The LTC4151-1/LTC4151-2 feature split I2C data pins to drive opto-isolators. The data out on the LTC4151-1 is inverted while that on the LTC4151-2 is not.
SKU: W017433 -
Power Management ICs - PMIC
Texas Instruments LM317AEMP
0 out of 5(0)The LM317AEMP/NOPB is an adjustable 3-terminal positive Voltage Regulator is capable of supplying in excess of 1.5A over a 1.2 to 37V output range. It is exceptionally easy to use and require only two external resistors to set the output voltage. Further, both line and load regulations are better than standard fixed regulators. In addition to higher performance than fixed regulators, the LM317AEMP/NOPB series offers full overload protection available only in IC’s. Included on the chip are current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional even if the adjustment terminal is disconnected.
- Specified 1% Output Voltage Tolerance
- Specified Maximum 0.01%/V Line Regulation
- Specified 1.5A Output Current
- Adjustable Output Down to 1.2V
- Current Limit Constant with Temperature
- P+ Product Enhancement Tested
- 80dB Ripple Rejection
- Output is Short-circuit Protected
- Green Product, No Sb/Br
SKU: W001862 -
Power Management ICs - PMIC
Infineon BTS50085-1TMB
0 out of 5(0)N channel vertical power FET with charge pump, current controlled input and diagnostic feedback with load current sense, integrated in Smart SIPMOS chip on chip technology. Providing embedded protection functions.
- Power switch with current sense diagnostic feedback for up to 48V DC grounded loads
- Most suitable for loads with high inrush current like lamps and motors; all types of resistive and inductive loads
- Replaces electromechanical relays, fuses and discrete circuits
SKU: W000332