| Number of Pins | 16 |
|---|---|
| REACH SVHC Compliance | No SVHC |
| Voltage Rating (DC) | 1.15 V |
| Packaging | Tube |
| Output Voltage | 70.0 V |
| RoHS | Compliant |
| Operating Temperature | 100 °C (max) |
| Number of Channels | 4 |
| Lead-Free Status | Lead Free |
| Isolation Voltage | 3.75 kV |
| Case/Package | SOP |
| Mounting Style | Surface Mount |
| Input Current | 5.00 mA |
Amplifiers & Comparators
| Manufacturer | Vishay |
|---|---|
| Manufacturer Part Number | SFH6916 |
| Description | OPTOISO 3.75KV 4CH TRANS 16-SOP |
| Stock Code | W005455 |
| Download |  Technical Datasheet |
The SFH6916 is a 4-channel Phototransistor Output Optocoupler has a GaAs infrared emitter, which is optically coupled to a silicon planar phototransistor detector. It features a high current transfer ratio, low coupling capacitance and high isolation voltage. The coupling device is designed for signal transmission between two electrically separated circuits.
- Low saturation voltage
- Fast switching times
- Temperature stable
Related products
- Amplifiers & Comparators
Analog Devices / Linear Technology LTC1540IMS8#PBF
The LTC1540IMS8#PBF is an ultralow nano-power single Comparator with built-in reference. The comparator features include less than 0.6µA supply current over the commercial temperature range, a 1.182V±2% reference, programmable hysteresis and TTL/CMOS outputs that sink and source current. The reference output can drive a bypass capacitor of up to 0.01µF without oscillation. The comparator operates from a single 2 to 11V supply or a dual ±1 to ±5.5V supply. Comparator hysteresis is easily programmed by using two resistors and the HYST pin. The comparator input operates from the negative supply to within 1.3V of the positive supply. The comparator output stage can continuously source up to 40mA. By eliminating the cross-conducting current that normally occur when the comparator changes logic states, power supply glitches are eliminated.
- Reference output drives 0.01µF capacitor
- Input voltage range includes the negative supply
- Reference output sources Up to 1mA
- 60µs Propagation delay with 10mV overdrive
- No crowbar current
- 40mA Continuous source current
- Pin-compatible with LTC1440, MAX921, MAX931
- LTADV Part marking
SKU: W000351 - Amplifiers & Comparators
Texas Instruments LM2903M
The LM2903M is a dual differential Independent Voltage Comparator designed to operate from a single power supply over a wide voltage range. It features ±1 to ±18V dual supply operation, 800mA typical low current drain and 25nA typical low input bias current.
- Allows comparison of voltages near ground potential
- Compatible with all forms of logic
- 800µA Low current drain
- 25nA Low input bias current
- ±5nA Low input offset current
- ±1mV Low offset voltage
SKU: W007776 - Amplifiers & Comparators
Texas Instruments LM7321MF/NOPB
The LM7321MF/NOPB is a single high output current Operational Amplifier with rail-to-rail input and output. The LM732xx family is efficient, achieving 18V/µs slew rate and 20MHz unity gain bandwidth while requiring only 1mA of supply current per op amp. The LM732xx device performance is fully specified for operation at 2.7V, ±5 and ±15V. The LM732xx device is designed to drive unlimited capacitive loads without oscillations. Greater than rail-to-rail input common-mode voltage range with 50dB of common-mode rejection across this wide voltage range, allows both high-side and low-side sensing. Most device parameters are insensitive to power supply voltage and this makes the parts easier to use where supply voltage may vary, such as automotive electrical systems and battery powered equipment. This amplifier has true rail-to-rail output and can supply a respectable amount of current (15mA) with minimal head-room from either rail (300mV) at low distortion (0.05% THD+noise).
- Capacitive load tolerance unlimited
- Input common-mode voltage of 0.3V beyond rails
- +65/-100mA Output current
- 15nV/√Hz Input voltage noise
- 1.3pA/√Hz Input current noise
- 1.1mA/channel Supply current
- -86dB Distortion THD+noise
- Green product and no Sb/Br
SKU: W000564 - Amplifiers & Comparators
Analog Devices AD8021ARZ
The AD8021ARZ is a Low Noise High Speed Voltage Feedback Amplifier that can be used in 16-bit resolution systems. It is designed to have both low voltage and low current noise (2.1nV/√Hz typical and 2.1pA/√Hz typical) while operating at the lowest quiescent supply current (7mA at ±5V) among today’s high speed, low noise op amps. An output disable pin allows further reduction of the quiescent supply current to 1.3mA. The AD8021 allows the user to choose the gain bandwidth product that best suits the application. It is also capable of driving a 75R line with ±3V video signals. The AD8021 is both technically superior and priced considerably less than comparable amps drawing much higher quiescent current. It is a high speed general-purpose amplifier, ideal for a wide variety of gain configurations and can be used throughout a signal processing chain and in control loops.
- Low noise
- Constant bandwidth from G = -1 to G = -10
- High speed
- 34mW or 6.7mA Typical low power for 5V supply
- Low distortion
- 1mV Maximum input offset voltage
- 0.5µV/°C Input offset voltage drift
SKU: W012311 - Amplifiers & Comparators
Texas Instruments TLV2465IN
The TLV246x is a family of low-power rail-to-rail input/output operational amplifiers specifically designed for portable applications. The input common-mode voltage range extends beyond the supply rails for maximum dynamic range in low-voltage systems. The amplifier output has rail-to-rail performance with high-output-drive capability, solving one of the limitations of older rail-to-rail input/output operational amplifiers. This rail-to-rail dynamic range and high output drive make the TLV246x ideal for buffering analog-to-digital converters.
SKU: W003182
