Sample Rate | 14.0 kHz |
---|---|
REACH SVHC Compliance | No SVHC |
Supply Current | 2.30 mA |
Supply Voltage (DC) | 4.75 V (min), 5.25 V (max) |
RoHS | Compliant |
Number of Pins | 20 |
Operating Temperature | -40.0 °C (min) |
Case/Package | TSSOP |
Lifecycle Status | Active |
Number of Bits | 12 |
Lead-Free Status | Lead Free |
Manufacturer | Analog Devices / Linear Technology |
---|---|
Manufacturer Part Number | LTC2309HF#PBF |
Description | 12BIT ADC, 8CH, 14KSPS, 20TSSOP |
Stock Code | W004190 |
Download | ![]() |
The LTC2309HF#PBF is a 8-channel 12-bit SAR Analog-to-digital Converter (ADC) with I²C compatible serial interface. This ADC includes an internal reference and a fully differential sample-and-hold circuit to reduce common mode noise. The ADC operates from an internal clock to achieve a fast 1.3µs conversion time. It operates from a single 5V supply and draws just 300µA at a throughput rate of 1ksps. The ADC enters nap mode when not converting, reducing the power dissipation. The low power consumption and small size make the ADC ideal for battery-operated and portable applications, while the 2-wire I²Ccompatibleserialinterfacemakes this ADC a good match for space-constrained systems.
- Guaranteed no missing codes
- Internal reference
- Internal 8-channel multiplexer
- Internal conversion clock
Related products
-
Data & Signal Conversion
Intersil ISLA214P50IRZ
0 out of 5(0)The ISLA214P50IRZ is a 14-bit Analog-to-digital Converter (ADC) designed with Intersils proprietary FemtoCharge™ technology on a standard CMOS process. The device utilizes two time-interleaved 250MSPS unit ADC to achieve the ultimate sample rate of 500MSPS. A single 500MHz conversion clock is presented to the converter and all interleave clocking is managed internally. The proprietary Intersil Interleave Engine performs automatic correction of offset, gain and sample time mismatches between the units ADC to optimize performance. A serial peripheral interface port allows for extensive configurability of the A/D. The SPI also controls the interleave correction circuitry, allowing the system to issue offline and continuous calibration commands as well as configure many dynamic parameters.
- Automatic fine interleave correction calibration
- Clock duty cycle stabilizer
- Programmable built-in test patterns
- SPI programmable fine gain and offset control
- Support for multiple ADC synchronization
- Optimized output timing
- Nap and sleep modes
- Data output clock
- DDR LVDS-compatible or LVCMOS outputs
- Selectable clock divider
SKU: W006837 -
Data & Signal Conversion
Texas Instruments TLC5540IPW
0 out of 5(0)The TLC5540 is a high-speed, 8-bit analog-to-digital converter (ADC) that converts at sampling rates up to 40 megasamples per second (MSPS). Using a semiflash architecture and CMOS process, the TLC5540 is able to convert at high speeds while still maintaining low power consumption and cost. The analog input bandwidth of 75 MHz (typ) makes this device an excellent choice for undersampling applications. Internal resistors are provided to generate 2-V full-scale reference voltages from a 5-V supply, thereby reducing external components.
The digital outputs can be placed in a high impedance mode. The TLC5540 requires only a single 5-V supply for operation.
SKU: W011862 -
Data & Signal Conversion
Microchip RN131G-I/RM
0 out of 5(0)RN131G-I/RM is a ultra low power WiFi 802.11 b/g surface mount module with on board antenna and U. FL connector. The WiFi module incorporates a 2.4GHz radio, processor, TCP/IP stack, real time clock, crypto accelerator, power management, and analog sensor interfaces. The module is preloaded with software to simplify integration and minimize application development. In the simplest configuration, the hardware requires only four connections (PWR, TX, RX, and GND) to create a wireless data connection. Additionally, the sensor interface provides temperature, audio, motion, acceleration, and other analog data without requiring additional hardware. The module is programmed and controlled with a simple ASCII command language. Once the module is set up, it can scan to find an access point, associate, authenticate, and connect over any WiFi network.
- Ultra low power with 4uA sleep, 40mA Rx, 210mA Tx
- High throughput, 1Mbps sustained data rate with TCP/IP and WPA2
- Small, compact surface mount module
- On board ceramic chip antenna and U. FL connector for external antenna
- UART hardware interface
- 10 general purpose digital I/O pins, 8 analog sensor interfaces
- Real time clock for wakeup and time stamping
- Accepts 3.3V regulated or 2V to 3V battery
- On board ECOS -OS, TCP/IP stacks
- Industrial grade temperature (-30°C to 85°C)
SKU: W005653 -
Data & Signal Conversion
Analog Devices AD9548BCPZ
0 out of 5(0)The AD9548 provides synchronization for many systems, including synchronous optical networks (SONET/SDH). The AD9548 generates an output clock synchronized to one of up to four differential or eight single-ended external input references. The digital PLL allows for reduction of input time jitter or phase noise associated with the external references. The AD9548 continuously generates a clean (low jitter), valid output clock even when all references have failed by means of a digitally controlled loop and holdover circuitry.
The AD9548 operates over an industrial temperature range of −40°C to +85°C.
- Supports Stratum 2 stability in holdover mode
- Supports reference switchover with phase build-out
- Supports hitless reference switchover
- Auto/manual holdover and reference switchover
- 4 pairs of reference input pins with each pair configurable as a single differential input or as 2 independent singleended inputs
- Input reference frequencies from 1 Hz to 750 MHz
- Reference validation and frequency monitoring (1 ppm)
- Programmable input reference switchover priority
- 30-bit programmable input reference divider
- 4 pairs of clock output pins with each pair configurable as a
- single differential LVDS/LVPECL output or as 2 singleended CMOS outputs
- Output frequencies up to 450 MHz
- 30-bit integer and 10-bit fractional programmable feedback divider
- Programmable digital loop filter covering loop bandwidths from 0.001 Hz to 100 kHz
- Optional low noise LC-VCO system clock multiplier
- Optional crystal resonator for system clock input
- On-chip EEPROM to store multiple power-up profiles
- Software controlled power-down
- 88-lead LFCSP package
SKU: W006838