| RoHS | Compliant |
|---|---|
| Number of Pins | 6 |
| Lifecycle Status | Active |
| Lead-Free Status | Contains Lead |
Power Management ICs - PMIC
| Manufacturer | Analog Devices |
|---|---|
| Manufacturer Part Number | LT6654AHS6-2.5 |
| Description | IC VREF SERIES 2.5V TSOT23-6 |
| Stock Code | W022312 |
| Download |  Technical Datasheet |
The LT®6654 is a family of small precision voltage references that offers high accuracy, low noise, low drift, low dropout and low power. The LT6654 operates from voltages up to 36V and is fully specified from –55°C to 125°C. A buffered output ensures ±10mA of output drive with low output impedance and precise load regulation. These features, in combination, make the
LT6654 ideal for portable equipment, industrial sensing and control, and automotive applications. The LT6654 was designed with advanced manufacturing techniques and curvature compensation to provide 10ppm/°C temperature drift and 0.05% initial accuracy. Low thermal hysteresis ensures high accuracy and 1.6ppmP-P noise minimizes measurement uncertainty. Since the LT6654 can also sink current, it can operate as a low power negative voltage reference with the same precision as a positive reference.
The LT6654 references are offered in 6-lead SOT-23 package and an 8-lead LS8 package. The LS8 is a 5mm × 5mm surface mount hermetic package that provides outstanding stability.
Related products
-
Power Management ICs - PMIC
Texas Instruments TPS2551QDBVRQ1
The TPS2551QDBVRQ1 is a Power Distribution Switch intended for applications in which heavy capacitive loads and short circuits are likely to be encountered. The current-limit threshold is user adjustable between 100mA and 1.1A via an external resistor. The power-switch rise and fall times are controlled to minimize current surges during switching. The device limits the output current to a desired level by switching into a constant-current mode when the output load exceeds the current-limit threshold or a short is present. An internal reverse-voltage detection comparator disables the power-switch in the event that the output voltage is driven higher than the input to protect devices on the input side of the switch. The FAULT logic output asserts low during both overcurrent and reverse-voltage conditions.
- 2µS Typical fast overcurrent response
- Reverse input-output voltage protection
- Deglitched fault report
- 1µA Maximum standby supply current
SKU: W000342 -
Power Management ICs - PMIC
Texas Instruments TPS767D301PWP
The TPS767D301PWP is a Dual-output Low-dropout (LDO) Voltage Regulator that offers fast transient response, low dropout voltages, dual outputs and incorporating stability with 10µF low ESR output capacitors. The TPS767D301 dual voltage regulator is designed primarily for DSP applications. This device can be used in any mixed-output voltage application, with each regulator supporting up to 1A. Dual active-low reset signals allow resetting of core-logic and I/O separately. Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low and is directly proportional to the output current. Additionally, since the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent of output loading (typically 85µA over the full range of output current, 0mA to 1A). These two key specifications yield a significant improvement in operating life for battery-powered systems.
- Dual output voltages for split-supply applications
- Output current range of 0mA to 1.0A per regulator
- 3.3/2.5, 3.3/1.8 and 3.3V/Adjustable output
- Fast-transient response
- 2% Tolerance over load and temperature
- 350mV Typical dropout voltage at 1A
- Ultra-low 85µA typical quiescent current
- 1µA Quiescent current during shutdown
- Dual open-drain power-on reset with 200ms delay for each regulator
- Thermal shutdown protection for each regulator
SKU: W007713 -
Power Management ICs - PMIC
Texas Instruments LP3963ES-3.3/NOPB
The LP3963ES-3.3/NOPB is a 3.3V fixed output fast ultra-low-dropout (LDO) Linear Regulator operate from a 2.5 to 7V input supply. This device respond very fast to step changes in load which makes them suitable for low voltage microprocessor applications. The device is developed on a CMOS process which allows low quiescent current operation independent of output load current. This CMOS process also allows the device to operate under extremely low-dropout (LDO) conditions. The dropout voltage is typically 80mV at 300mA load current and 800mV at 3A load current.
- Low ground pin current
- 0.06% Load regulation
- 15µA Quiescent current in shutdown mode
- ±1.5% Output voltage accuracy
- ERROR flag indicates output status
- Minimum output capacitor requirements
- Overtemperature and overcurrent protection
SKU: W006996 -
Power Management ICs - PMIC
Analog Devices / Linear Technology LT3012BEFE#PBF
The LT® 3012B is a high voltage, micropower low dropout linear regulator. The device is capable of supplying 250mA of output current with a dropout voltage of 400mV. Designed for use in battery-powered or high voltage systems, the low quiescent current (40µA operating) makes the LT3012B an ideal choice. Quiescent current is also well controlled in dropout.
Other features of the LT3012B include the ability to operate with very small output capacitors. The regulators are stable with only 3.3µF on the output while most older devices require between 10µF and 100µF for stability. Small ceramic capacitors can be used without any need for series resistance (ESR) as is common with other regulators. Internal protection circuitry includes reverse-battery protection, current limiting, thermal limiting and reverse current protection.
The device is available with an adjustable output with a 1.24V reference voltage. The LT3012B regulator is available in the 16-lead TSSOP and 12 pin low profile (0.75mm) (4mm × 3mm) DFN packages with an exposed pad for enhanced thermal handling capability.
- Wide Input Voltage Range: 4V to 80V
- Low Quiescent Current: 40µA
- Low Dropout Voltage: 400mV
- Output Current: 250mA
- No Protection Diodes Needed
- Adjustable Output from 1.24V to 60V
- Stable with 3.3µF Output Capacitor
- Stable with Aluminum, Tantalum or Ceramic Capacitors
- Reverse-Battery Protection
- No Reverse Current Flow from Output to Input
- Thermal Limiting
- Thermally Enhanced 16-Lead TSSOP and 12-Pin(4mm × 3mm) DFN Packages
SKU: W002018
