| RoHS | Compliant |
|---|---|
| REACH SVHC Compliance | No SVHC |
| Packaging | Tube |
| Mounting Style | Surface Mount |
Power Management ICs - PMIC
| Manufacturer | Bourns |
|---|---|
| Manufacturer Part Number | SM-LP-5001 |
| Description | TRANSFORMBER LINE MATCHING SMD |
| Stock Code | W002736 |
| Download |  Technical Datasheet |
The SM-LP-5001E is a line matching Audio Transformer, 1:1 turn ratio, 600Ω primary/secondary impedance with Sn/Ag/Cu terminal plating and surface mount. This transformer features subminiature in SMT, distortion of 0.015%, vacuum encapsulated. Suitable for modems (V32).
- 7.36mm Seated height
- 24dB at 200 to 4kHz Return loss
- 115Ω ±15% Primary/Secondary DC resistance
- -20 to 85°C Operating temperature range
Related products
-
Power Management ICs - PMIC
Texas Instruments TPS73701DCQ
The TPS73701DCQ is a linear low-dropout (LDO) Voltage Regulator uses an NMOS pass element in a voltage-follower configuration. This topology is relatively insensitive to output capacitor value and ESR, allowing a wide variety of load configurations. Load transient response is excellent, even with a small 1µF ceramic output capacitor. The NMOS topology also allows very low dropout. This device uses an advanced BiCMOS process to yield high precision while delivering very low dropout voltages and low ground pin current. Current consumption, when not enabled, is less than 20nA and ideal for portable applications. This device is protected by thermal shutdown and fold-back current limit. It features reverse current blockage and freedom from output capacitor constraints. These features combined with an enable input makes the device ideal for portable applications.
- Thermal shutdown and current limit for fault protection
- Excellent load transient response-even with only 1µF output capacitor
- 1% Initial accuracy
- 3% Overall accuracy over line, load and temperature
- Less than 20nA typical IQ in shutdown mode
- Green product and no Sb/Br
SKU: W000341 -
Power Management ICs - PMIC
Texas Instruments TPS767D301PWP
The TPS767D301PWP is a Dual-output Low-dropout (LDO) Voltage Regulator that offers fast transient response, low dropout voltages, dual outputs and incorporating stability with 10µF low ESR output capacitors. The TPS767D301 dual voltage regulator is designed primarily for DSP applications. This device can be used in any mixed-output voltage application, with each regulator supporting up to 1A. Dual active-low reset signals allow resetting of core-logic and I/O separately. Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low and is directly proportional to the output current. Additionally, since the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent of output loading (typically 85µA over the full range of output current, 0mA to 1A). These two key specifications yield a significant improvement in operating life for battery-powered systems.
- Dual output voltages for split-supply applications
- Output current range of 0mA to 1.0A per regulator
- 3.3/2.5, 3.3/1.8 and 3.3V/Adjustable output
- Fast-transient response
- 2% Tolerance over load and temperature
- 350mV Typical dropout voltage at 1A
- Ultra-low 85µA typical quiescent current
- 1µA Quiescent current during shutdown
- Dual open-drain power-on reset with 200ms delay for each regulator
- Thermal shutdown protection for each regulator
SKU: W007713 -
Power Management ICs - PMIC
Texas Instruments LM317AEMP
The LM317AEMP/NOPB is an adjustable 3-terminal positive Voltage Regulator is capable of supplying in excess of 1.5A over a 1.2 to 37V output range. It is exceptionally easy to use and require only two external resistors to set the output voltage. Further, both line and load regulations are better than standard fixed regulators. In addition to higher performance than fixed regulators, the LM317AEMP/NOPB series offers full overload protection available only in IC’s. Included on the chip are current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional even if the adjustment terminal is disconnected.
- Specified 1% Output Voltage Tolerance
- Specified Maximum 0.01%/V Line Regulation
- Specified 1.5A Output Current
- Adjustable Output Down to 1.2V
- Current Limit Constant with Temperature
- P+ Product Enhancement Tested
- 80dB Ripple Rejection
- Output is Short-circuit Protected
- Green Product, No Sb/Br
SKU: W001862
