Number of Pins | 7 |
---|---|
REACH SVHC Compliance | No SVHC |
RoHS | Compliant |
Packaging | Tube |
Operating Temperature | -40.0 °C (min) |
Lead-Free Status | Lead Free |
Mounting Style | Through Hole |
Manufacturer | Infineon |
---|---|
Manufacturer Part Number | BTS50085-1TMB |
Description | IC SWITCH PWR HISIDE TO220-7 |
Stock Code | W000332 |
Download | ![]() |
N channel vertical power FET with charge pump, current controlled input and diagnostic feedback with load current sense, integrated in Smart SIPMOS chip on chip technology. Providing embedded protection functions.
- Power switch with current sense diagnostic feedback for up to 48V DC grounded loads
- Most suitable for loads with high inrush current like lamps and motors; all types of resistive and inductive loads
- Replaces electromechanical relays, fuses and discrete circuits
Related products
-
Power Management ICs - PMIC
Texas Instruments TPS27081ADDCR
0 out of 5(0)The TPS27081ADDCR is a high-side Load Switch features industry-standard ESD protection on all pins providing better ESD compatibility with other on board components. The TPS27081A level shifts ON/OFF logic signal to VIN levels and supports as low as 1-V CPU or MCU logic to control higher voltage power supplies without requiring an external level-shifter. Switching a large value output capacitor CL through a fast ON/OFF logic signal may result in an excessive inrush current. To control the load inrush current, connect a resistor R2 and add an external capacitor C1 as shown in the Simplified Schematic in the Technical Data Sheet. To configure the TPS27081A to achieve a specific slew rate, refer to the Application and Implementation section. A single pull-up resistor R1 is required in standby power switch applications. In such applications connect the R2 pin of the TPS27081A to the system ground when inrush current control is not required.
- Adjustable turn-on and turnoff slew rate control through external R1, R2 and C1
- Supports a wide range of 1.2 to 8V supply inputs
- Integrated NMOS for PFET control
- Full ESD protection (all pins)
- Low ON-resistance, high-current PFET
- Ultralow leakage current in standby (typical 100nA)
SKU: W008212 -
Power Management ICs - PMIC
Texas Instruments LP38855S-1.2
0 out of 5(0)The LP38855S-1.2 is a 1.8V fixed output fast-response high-accuracy low-dropout (LDO) Linear Regulator with Enable. The device can maintain output voltage regulation with an extremely low input to output voltage drop. Fabricated on a CMOS process, the device operates from two input voltages, VBIAS provides power for the internal bias and control circuits, as well as drive for the gate of the N-MOS power transistor, while VIN supplies power to the load. The use of an external bias rail allows the part to operate from ultra-low VIN voltages. Unlike bipolar regulators, the CMOS architecture consumes extremely low quiescent current at any output load current. The use of an N-MOS power transistor results in wide bandwidth, yet minimum external capacitance is required to maintain loop stability. The fast transient response of this device makes it suitable for use in powering DSP, microcontroller core voltages and switch mode power supply post regulators.
- Stable with 10µF ceramic capacitors
- ±1.0% Precision output voltage across all line and load conditions (TJ = 25°C)
- Overtemperature and overcurrent protection
SKU: W002951 -
Power Management ICs - PMIC
Texas Instruments LP3963ES-3.3/NOPB
0 out of 5(0)The LP3963ES-3.3/NOPB is a 3.3V fixed output fast ultra-low-dropout (LDO) Linear Regulator operate from a 2.5 to 7V input supply. This device respond very fast to step changes in load which makes them suitable for low voltage microprocessor applications. The device is developed on a CMOS process which allows low quiescent current operation independent of output load current. This CMOS process also allows the device to operate under extremely low-dropout (LDO) conditions. The dropout voltage is typically 80mV at 300mA load current and 800mV at 3A load current.
- Low ground pin current
- 0.06% Load regulation
- 15µA Quiescent current in shutdown mode
- ±1.5% Output voltage accuracy
- ERROR flag indicates output status
- Minimum output capacitor requirements
- Overtemperature and overcurrent protection
SKU: W011855 -
Power Management ICs - PMIC
Texas Instruments LM337IMP
0 out of 5(0)The LM337IMP is a three terminal adjustable negative voltage regulator in 4 pin SOT-223 package. This regulator is exceptionally easy to apply and requires only two external resistors to set output voltage and one output capacitor for frequency compensation. The circuit design has been optimized for excellent regulation and low thermal transients. The LM137 features internal current limiting, thermal shut down and safe area compensation by making them virtually blowout proof against overloads. This positive voltage regulator is used in wide variety of applications including local on-card regulation, programmable output voltage regulation or precision current regulation.
- Adjustable output voltage from -1.2V to -37V
- 1.5A output current
- Input voltage range from -4.2V to -50V
- Line regulation is typically 0.01%/V
- Load regulation is typically 0.3%
- Excellent thermal regulation of 0.002%/W
- Ripple rejection ratio of 77dB
- Output is short circuit protected
- Operating temperature range -40°C to 125°C
- 50ppm/°C temperature coefficient
SKU: W022650