Rise Time | 20.0 ns (max) |
---|---|
Number of Channels | 2 |
Number of Outputs | 2 |
Lifecycle Status | Active |
Operating Temperature | -40.0 °C to 85.0 °C |
Case/Package | SOIC |
Lead-Free Status | Lead Free |
Output Current | 2.00 A |
Number of Pins | 8 |
REACH SVHC Compliance | No SVHC |
RoHS | Compliant |
Power Dissipation | 570 mW (max) |
Output Voltage | 16.5 V |
Supply Voltage (DC) | 4.50 V (min), 15.0 V (max) |
Packaging | Bulk |
Mounting Style | Surface Mount |
Manufacturer | Intersil |
---|---|
Manufacturer Part Number | EL7202CSZ |
Description | Gate Drivers EL7202CSZ DL MSFT DRVR |
Stock Code | W005573 |
Download | ![]() |
The EL7202CSZ is a high speed matched dual-channel Power MOSFET Driver improves the operation of the industry standard DS0026 clock driver. The Elantec versions are very high speed drivers capable of delivering peak currents of 2A into highly capacitive loads. The high speed performance is achieved by means of a proprietary Turbo-Driver circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. These matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with non-overlapped drive techniques.
- Industry standard driver replacement
- Improved response times
- Matched rise and fall times
- Reduced clock skew
- Low output impedance
- Low input capacitance
- High noise immunity
- Improved clocking rate
- Low supply current
- Wide operating range
Related products
-
Power Management ICs - PMIC
Analog Devices / Linear Technology LT3012BEFE#PBF
0 out of 5(0)The LT® 3012B is a high voltage, micropower low dropout linear regulator. The device is capable of supplying 250mA of output current with a dropout voltage of 400mV. Designed for use in battery-powered or high voltage systems, the low quiescent current (40µA operating) makes the LT3012B an ideal choice. Quiescent current is also well controlled in dropout.
Other features of the LT3012B include the ability to operate with very small output capacitors. The regulators are stable with only 3.3µF on the output while most older devices require between 10µF and 100µF for stability. Small ceramic capacitors can be used without any need for series resistance (ESR) as is common with other regulators. Internal protection circuitry includes reverse-battery protection, current limiting, thermal limiting and reverse current protection.
The device is available with an adjustable output with a 1.24V reference voltage. The LT3012B regulator is available in the 16-lead TSSOP and 12 pin low profile (0.75mm) (4mm × 3mm) DFN packages with an exposed pad for enhanced thermal handling capability.
- Wide Input Voltage Range: 4V to 80V
- Low Quiescent Current: 40µA
- Low Dropout Voltage: 400mV
- Output Current: 250mA
- No Protection Diodes Needed
- Adjustable Output from 1.24V to 60V
- Stable with 3.3µF Output Capacitor
- Stable with Aluminum, Tantalum or Ceramic Capacitors
- Reverse-Battery Protection
- No Reverse Current Flow from Output to Input
- Thermal Limiting
- Thermally Enhanced 16-Lead TSSOP and 12-Pin(4mm × 3mm) DFN Packages
SKU: W002018 -
Power Management ICs - PMIC
Texas Instruments TPS27081ADDCR
0 out of 5(0)The TPS27081ADDCR is a high-side Load Switch features industry-standard ESD protection on all pins providing better ESD compatibility with other on board components. The TPS27081A level shifts ON/OFF logic signal to VIN levels and supports as low as 1-V CPU or MCU logic to control higher voltage power supplies without requiring an external level-shifter. Switching a large value output capacitor CL through a fast ON/OFF logic signal may result in an excessive inrush current. To control the load inrush current, connect a resistor R2 and add an external capacitor C1 as shown in the Simplified Schematic in the Technical Data Sheet. To configure the TPS27081A to achieve a specific slew rate, refer to the Application and Implementation section. A single pull-up resistor R1 is required in standby power switch applications. In such applications connect the R2 pin of the TPS27081A to the system ground when inrush current control is not required.
- Adjustable turn-on and turnoff slew rate control through external R1, R2 and C1
- Supports a wide range of 1.2 to 8V supply inputs
- Integrated NMOS for PFET control
- Full ESD protection (all pins)
- Low ON-resistance, high-current PFET
- Ultralow leakage current in standby (typical 100nA)
SKU: W008212 -
Power Management ICs - PMIC
Texas Instruments LM337IMP
0 out of 5(0)The LM337IMP is a three terminal adjustable negative voltage regulator in 4 pin SOT-223 package. This regulator is exceptionally easy to apply and requires only two external resistors to set output voltage and one output capacitor for frequency compensation. The circuit design has been optimized for excellent regulation and low thermal transients. The LM137 features internal current limiting, thermal shut down and safe area compensation by making them virtually blowout proof against overloads. This positive voltage regulator is used in wide variety of applications including local on-card regulation, programmable output voltage regulation or precision current regulation.
- Adjustable output voltage from -1.2V to -37V
- 1.5A output current
- Input voltage range from -4.2V to -50V
- Line regulation is typically 0.01%/V
- Load regulation is typically 0.3%
- Excellent thermal regulation of 0.002%/W
- Ripple rejection ratio of 77dB
- Output is short circuit protected
- Operating temperature range -40°C to 125°C
- 50ppm/°C temperature coefficient
SKU: W022650