| Output Current | 500 mA |
|---|---|
| Packaging | Cut Tape (CT), Tape & Reel (TR) |
| Number of Pins | 3 |
| RoHS | Compliant |
| Output Voltage | 5.20 V (max), 4.80 V (min), 5.00 V (max) |
| REACH SVHC Compliance | No SVHC |
| Operating Temperature | 150 °C (max) |
| Number of Outputs | 1 |
| Lead-Free Status | Lead Free |
| Input Voltage (DC) | 20.0 V (max) |
| Lifecycle Status | Active |
| Mounting Style | Surface Mount |
| Dropout Voltage | 2.00 V |
Power Management ICs - PMIC
| Manufacturer | STMicroelectronics |
|---|---|
| Manufacturer Part Number | L78M05CDT-TR |
| Description | IC REG LDO 5V 0.5A DPAK |
| Stock Code | W002734 |
| Download |  Technical Datasheet |
The L78M05CDT-TR is a three-terminal positive Voltage Regulator with several fixed output voltages, making it useful in a wide range of applications. This regulator can provide local on-card regulation, eliminating the distribution problems associated with single point regulation. Each type employs internal current limiting, thermal shutdown and safe area protection, resulting it essentially indestructible. If adequate heat sinking is provided, they can deliver over 0.5A output current. Although designed primarily as fixed voltage regulators, these devices can be used with external components to obtain adjustable voltage and currents.
- Thermal Overload Protection
- Short-circuit Protection
- Output Transition SOA Protection
- 4% Output Voltage Tolerance
- Guaranteed in Extended Temperature Range
Related products
-
Power Management ICs - PMIC
Texas Instruments TPS2551QDBVRQ1
The TPS2551QDBVRQ1 is a Power Distribution Switch intended for applications in which heavy capacitive loads and short circuits are likely to be encountered. The current-limit threshold is user adjustable between 100mA and 1.1A via an external resistor. The power-switch rise and fall times are controlled to minimize current surges during switching. The device limits the output current to a desired level by switching into a constant-current mode when the output load exceeds the current-limit threshold or a short is present. An internal reverse-voltage detection comparator disables the power-switch in the event that the output voltage is driven higher than the input to protect devices on the input side of the switch. The FAULT logic output asserts low during both overcurrent and reverse-voltage conditions.
- 2µS Typical fast overcurrent response
- Reverse input-output voltage protection
- Deglitched fault report
- 1µA Maximum standby supply current
SKU: W000342 -
Power Management ICs - PMIC
Texas Instruments LP3963ES-3.3/NOPB
The LP3963ES-3.3/NOPB is a 3.3V fixed output fast ultra-low-dropout (LDO) Linear Regulator operate from a 2.5 to 7V input supply. This device respond very fast to step changes in load which makes them suitable for low voltage microprocessor applications. The device is developed on a CMOS process which allows low quiescent current operation independent of output load current. This CMOS process also allows the device to operate under extremely low-dropout (LDO) conditions. The dropout voltage is typically 80mV at 300mA load current and 800mV at 3A load current.
- Low ground pin current
- 0.06% Load regulation
- 15µA Quiescent current in shutdown mode
- ±1.5% Output voltage accuracy
- ERROR flag indicates output status
- Minimum output capacitor requirements
- Overtemperature and overcurrent protection
SKU: W006996 -
Power Management ICs - PMIC
Texas Instruments LM317AEMP
The LM317AEMP/NOPB is an adjustable 3-terminal positive Voltage Regulator is capable of supplying in excess of 1.5A over a 1.2 to 37V output range. It is exceptionally easy to use and require only two external resistors to set the output voltage. Further, both line and load regulations are better than standard fixed regulators. In addition to higher performance than fixed regulators, the LM317AEMP/NOPB series offers full overload protection available only in IC’s. Included on the chip are current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional even if the adjustment terminal is disconnected.
- Specified 1% Output Voltage Tolerance
- Specified Maximum 0.01%/V Line Regulation
- Specified 1.5A Output Current
- Adjustable Output Down to 1.2V
- Current Limit Constant with Temperature
- P+ Product Enhancement Tested
- 80dB Ripple Rejection
- Output is Short-circuit Protected
- Green Product, No Sb/Br
SKU: W001862
