REACH SVHC Compliance | No SVHC |
---|---|
Operating Temperature | -55.0 °C (min) |
Slew Rate | 500 mV/μs |
Number of Channels | 4 |
Packaging | Cut Tape (CT), Tape & Reel (TR) |
RoHS | Compliant |
Number of Pins | 14 |
Mounting Style | Surface Mount |
Input Offset Drift | 7.00 µV/K |
Bandwidth | 1.20 MHz |
Lifecycle Status | Active |
Case/Package | SOIC |
Lead-Free Status | Lead Free |
Gain Bandwidth Product | 1.20 MHz |
Manufacturer | Texas Instruments |
---|---|
Manufacturer Part Number | LM124DRG4 |
Description | IC OPAMP GP 1.2MHZ 14SOIC |
Stock Code | W010675 |
Download | ![]() |
The LM124DRG4 is a 4 independent high-gain frequency-compensated Operational Amplifier designed specifically to operate from a single supply or split supply over a wide range of voltages.
- Internal frequency compensation
- Common-mode input voltage range includes ground, allowing direct sensing near ground
- Low input bias and offset parameters
- 2kV ESD Protection
- 0.8mA Typical low supply-current drain independent of supply voltage
- 3mV Typical input offset voltage
- 2nA Typical input offset current
- 20nA Typical input bias current
- 32V Differential input voltage range equal to maximum-rated supply voltage
- 100V/mV Typical open-loop differential voltage amplification
Related products
-
Amplifiers & Comparators
Texas Instruments LM386N-1/NOPB
0 out of 5(0)The LM386N-1/NOPB is a Wide Vin Class-D low Power Audio Amplifier with internal gain designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but the addition of an external resistor and capacitor between pins 1 and 8 will increase the gain to any value from 20 to 200. The inputs are ground referenced while the output automatically biases to one-half the supply voltage. The quiescent power drain is only 24mW when operating from a 6V supply, making the LM386 ideal for battery operation.
- Battery operation
- Minimum external parts
- Low quiescent current drain
- Ground referenced input
- Self-centering output quiescent voltage
- Green product and no Sb/Br
SKU: W006347 -
Amplifiers & Comparators
Analog Devices AD8021ARZ
0 out of 5(0)The AD8021ARZ is a Low Noise High Speed Voltage Feedback Amplifier that can be used in 16-bit resolution systems. It is designed to have both low voltage and low current noise (2.1nV/√Hz typical and 2.1pA/√Hz typical) while operating at the lowest quiescent supply current (7mA at ±5V) among today’s high speed, low noise op amps. An output disable pin allows further reduction of the quiescent supply current to 1.3mA. The AD8021 allows the user to choose the gain bandwidth product that best suits the application. It is also capable of driving a 75R line with ±3V video signals. The AD8021 is both technically superior and priced considerably less than comparable amps drawing much higher quiescent current. It is a high speed general-purpose amplifier, ideal for a wide variety of gain configurations and can be used throughout a signal processing chain and in control loops.
- Low noise
- Constant bandwidth from G = -1 to G = -10
- High speed
- 34mW or 6.7mA Typical low power for 5V supply
- Low distortion
- 1mV Maximum input offset voltage
- 0.5µV/°C Input offset voltage drift
SKU: W012311 -
Amplifiers & Comparators
Texas Instruments LM7321MF/NOPB
0 out of 5(0)The LM7321MF/NOPB is a single high output current Operational Amplifier with rail-to-rail input and output. The LM732xx family is efficient, achieving 18V/µs slew rate and 20MHz unity gain bandwidth while requiring only 1mA of supply current per op amp. The LM732xx device performance is fully specified for operation at 2.7V, ±5 and ±15V. The LM732xx device is designed to drive unlimited capacitive loads without oscillations. Greater than rail-to-rail input common-mode voltage range with 50dB of common-mode rejection across this wide voltage range, allows both high-side and low-side sensing. Most device parameters are insensitive to power supply voltage and this makes the parts easier to use where supply voltage may vary, such as automotive electrical systems and battery powered equipment. This amplifier has true rail-to-rail output and can supply a respectable amount of current (15mA) with minimal head-room from either rail (300mV) at low distortion (0.05% THD+noise).
- Capacitive load tolerance unlimited
- Input common-mode voltage of 0.3V beyond rails
- +65/-100mA Output current
- 15nV/√Hz Input voltage noise
- 1.3pA/√Hz Input current noise
- 1.1mA/channel Supply current
- -86dB Distortion THD+noise
- Green product and no Sb/Br
SKU: W000564 -
Amplifiers & Comparators
Texas Instruments TLV3704IPWR
0 out of 5(0)Comparator General Purpose CMOS, Push-Pull, Rail-to-Rail 14-TSSOP
The TLV370x is Texas Instruments’ first family of nanopower comparators with only 560 nA per channel supply current, which make this device ideal for battery power and wireless handset applications. The TLV370x has a minimum operating supply voltage of 2.7 V over the extended industrial temperature range (TA = –40°C to 125°C), while having an input common-mode range of –0.1 to VCC + 5 V. The low supply current makes it an ideal choice for battery-powered portable applications where quiescent current is the primary concern.
Reverse battery protection guards the amplifier from an overcurrent condition due to improper battery installation. For harsh environments, the inputs can be taken 5 V above the positive supply rail without damage to the device.
All members are available in PDIP and SOIC with the singles in the small SOT-23 package, duals in the MSOP, and quads in the TSSOP package.
SKU: W023526